[linux-dvb] now my TT-DVB-T works (partial) (was: a little progress)

[Nils Ohlmeier <nils.ohlmeier@web.de>]

Hi,

the pids were the right hint. Thanks to Juri for sending me the actual  
channels.conf for Berlins DVB-T. Sadly it was for vdr again. So i merged it 
with the channels.conf-dvbt-berlin from CVS. Result:

ntv:650000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_1_2:FEC_NONE:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:273:274
Sat1:658000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:385:386
RTL:658000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:337:338
RTL2:658000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:353:354
Pro7:658000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:305:306
VOX:778000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:545:546
Kabel1:778000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:161:162
MTV:650000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:193:194
N24:778000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:225:226
SuperRTL:778000000:INVERSION_OFF:BANDWIDTH_8_MHZ:FEC_2_3:FEC_NONE:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE:433:434

I omitted channels which i wasn't able to receive (e.g. ZDF, ZDFinfo...). 
Maybe someone can change this in CVS after adding the missing channels, so 
that nobody else ran into this problem again.

But i have still a problem with the driver: after trying to switch to wrongly 
configured channel nothing works anymore. Switching to a correct channel 
results only in the values of the wrong channel before. I have to reload the 
driver again before it works again.
So switching to my wrong configured ZDF wasn't a good hint Juri ;-)

Thank you very much for you patience and support.

  Nils

On Friday 22 November 2002 15:19, Jürgen Peitz wrote:
> Am Freitag, 22. November 2002 11:04 schrieb Nils Ohlmeier:
> > Hi,
> >
> > after a lot of testing (w/ and w/o my WinTV card installed; w/o ACPI and
> > APIC...) i have now a little bit progress...
> > With a vanilla kernel 'tzap ZDF' gives me (sometimes):
> >
> > status 17 | signal 1717 | snr 00000 | ber 00000 | unc 00000 | FE_HAS_LOCK
>
> the value for the signal is not very high. Do you get better values if you
> tune to PRO7 or RTL.
>
> > but i still have no picture :-(
>
> Do you use the latest channels.conf ? Maybe your values for the video pids
> are not correct.



--
Info:
To unsubscribe send a mail to listar@linuxtv.org with "unsubscribe linux-dvb" as subject.