[linux-dvb] Re: Full featured card summary

[Holger Waechtler <holger@qanu.de>]

On Sunday 14 March 2004 14:45, Andrew de Quincey wrote:
> On Sunday 14 March 2004 13:35, you wrote:
> > Andrew de Quincey wrote:
> > > > The two combinations below are working with the _unmodified_ ves1x93
> > > > code and also with my alps_bsvr2 mod.
> > > >
> > > > S13E    11700 V  9750 v [E0 10 38 F0]
> > > > S13E    99999 V 10600 v [E0 10 38 F1]
> > > > S13E    11700 H  9750 v [E0 10 38 F2]
> > > > S13E    99999 H 10600 v [E0 10 38 F3]
> > > > S19.2E  11700 V  9750 v [E0 10 38 F4]
> > > > S19.2E  99999 V 10600 v [E0 10 38 F5]
> > > > S19.2E  11700 H  9750 v [E0 10 38 F6]
> > > > S19.2E  99999 H 10600 v [E0 10 38 F7]
> > > >
> > > > S13E    11700 V  9750 v [E0 10 38 F0] [E1 10 38 F0] [E1 10 38 F0]
> > > > S13E    99999 V 10600 v [E0 10 38 F1] [E1 10 38 F1] [E1 10 38 F1]
> > > > S13E    11700 H  9750 v [E0 10 38 F2] [E1 10 38 F2] [E1 10 38 F2]
> > > > S13E    99999 H 10600 v [E0 10 38 F3] [E1 10 38 F3] [E1 10 38 F3]
> > > > S19.2E  11700 V  9750 v [E0 10 38 F4] [E1 10 38 F4] [E1 10 38 F4]
> > > > S19.2E  99999 V 10600 v [E0 10 38 F5] [E1 10 38 F5] [E1 10 38 F5]
> > > > S19.2E  11700 H  9750 v [E0 10 38 F6] [E1 10 38 F6] [E1 10 38 F6]
> > > > S19.2E  99999 H 10600 v [E0 10 38 F7] [E1 10 38 F7] [E1 10 38 F7]
> > > >
> > > >
> > > > @Andrew: Thanks for code-digging that much. Do you understand the
> > > > difference?
> > >
> > > I get you, its the 'v'. Previously the driver was turning voltage on
> > > when it started up, so power was being supplied, whereas now by default
> > > leaves it off.
> >
> > So this means VDR should turn the voltage _on_ upon startup, right?
> > I don't think having to do this via the DiSEqC configuration is the
> > way to go...

Specifying 13V or 18V is kind of voltage on, isn't it? For sure you need to 
enable the LNBP in these cases.

Holger


-- 
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.