[linux-dvb] Re: List of Frontends/PLLs used by DVB devices

[Oliver Endriss <o.endriss@gmx.de>]

On Montag, 20. September 2004 02:48, Andrew de Quincey wrote:
> On Sunday 19 Sep 2004 01:51, Oliver Endriss wrote:
> > On Sonntag, 19. September 2004 02:19, Andrew de Quincey wrote:
> > > Thanks a lot! another few off the list.
> > >
> > > > card description: Siemens/Technotrend/Hauppauge PCI rev1.3
> > > > card driver: dvb-ttpci
> > > > frontend driver: ves1x93
> > > > frontend location: tin box
> > > > tin box: ALPS BSRV2-301A
> > > > interface: PCI
> > > > PCI device id: 1131:7146
> > > > PCI subsystem id: 0x13c2:0x0000
> > > >
> > > > > Technotrend/Hauppauge PCI rev?(unknown0)?             -- 0x13c2,
> > > > > 0x1002
> > > >
> > > > card description: Siemens/Technotrend/Hauppauge PCI rev1.3
> > > > card driver: dvb-ttpci
> > > > frontend driver: ves1x93
> > > > frontend location: tin box
> > > > tin box: ALPS BSRV2-301A
> > > > interface: PCI
> > > > PCI device id: 1131:7146
> > > > PCI subsystem id: 0x13c2:0x1002
> > >
> > > Is the EEPROM occasionally bad? You've given two definitions for the 1.3
> > > cards with different subsystem Ids... and also Peter Siering gave the
> > > 13c2:0000 one as matching his rev 1.5 card!
> >
> > I have *two* Rev 1.3 cards with id 0x13c2:0x0000. So the id is correct.
> >
> > I know from several postings at vdr-portal that Rev 1.5 cards are
> > currently (mis)identified by the driver as rev 1.3 cards.
> > Imho they use the same id as rev 1.3 cards, but have a different
> > frontend. :(
> 
> Hi - you misunderstood slightly - I agree that the rev1.3 is 0x13c2:0x0000. 

Ok.

> The question I was asking was about the rev1.3 you've put as subsystem ID 
> 0x13c2:0x1002 above... I would have expected that card to be in the revision 
> 2.x range. I'm assuming all DVB-S fullfeatured rev1.x cards were 
> 0x13c2:0x0000 - so far everything has matched this except the one above. Can 
> you confirm so I know if I'm right or wrong in that assumption?

Well, I only have one rev 1.3 card with id  0x13c2:0x1002, so the
EEPROM contents might be wrong. But the card differs slightly:

id		component side               solder side           LNBP chip   CI connector
13c2/0000       Sat-DVB Rev.: 1.3 TTC99.04   BTI ML-1 94V-0 1000   16SP        C on solder side
13c2/1002       Sat-DVB Rev.: 1.3 TTC99.04   CT 002V0 94V-0 9942   13SP        no C

Imho we have these full-featured DVB-S cards:
> 13c2/0000 Hauppauge WinTV DVB-S
rev 1.3/1.5/1.6

> 13c2/0003 Hauppauge WinTV Nexus-S
rev 2.1
??? rev 2.2 ???

> 13c2/0006 Hauppauge WinTV DVB-S
???

> 13c2/1002 Hauppauge WinTV DVB-S
rev 1.3 special edition ;-) ???

CU
Oliver

-- 
--------------------------------------------------------
VDR Remote Plugin available at
http://endriss.escape.bei.t-online.de/vdr/
--------------------------------------------------------