[linux-dvb] Re: budget hang after EPG scan (Was: Re: cinergyT2: which kernel/usb module to use?)

[Manu Abraham <manu@kromtek.com>]

On Sun December 5 2004 1:58 pm, Simon wrote:
> Andrew de Quincey wrote:
> > On Saturday 04 Dec 2004 11:13, Simon wrote:
>
> [...]
>
> >>Im using vanilla 2.6.8.1 kernel + patch listed at the end.
> >>2xTwinhan DVB-T cards.
> >>Slackware 10, VDR-1.3.12+patches and vdradmin-0.96.
> >
> > Aarrgh, so this was the same problem - that everything appears to works
> > fine, its just that there is no data from the budget cards?
> >
> > Which Twinhan cards are they BTW?
>
> not sure what you want, so:
>
> from dmesg:
> Linux video capture interface: v1.00
> bttv: driver version 0.9.15 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
> bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 11, latency: 32, mmio:
> 0xde011000
> bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID
> is 1822:0001
> bttv0: using: Twinhan DST + clones [card=113,insmod option]
> bttv0: gpio: en=00000000, out=00000000 in=00fb7afe [init]
> bttv0: using tuner=4
> bttv0: add subdevice "dvb0"
> bttv: Bt8xx card found (1).
> ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 5 (level, low) -> IRQ 5
> bttv1: Bt878 (rev 17) at 0000:00:0b.0, irq: 5, latency: 32, mmio:
> 0xde013000 bttv1: detected: Twinhan VisionPlus DVB-T [card=113], PCI
> subsystem ID is 1822:0001
> bttv1: using: Twinhan DST + clones [card=113,autodetected]
> bttv1: gpio: en=00000000, out=00000000 in=00fb4bfe [init]
> bttv1: using tuner=4
> bttv1: add subdevice "dvb1"
> bt878: AUDIO driver version 0.0.0 loaded
> bt878: Bt878 AUDIO function found (0).
> ACPI: PCI interrupt 0000:00:0a.1[A] -> GSI 11 (level, low) -> IRQ 11
> bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 11, latency: 32, memory:
> 0xde012000
> bt878: Bt878 AUDIO function found (1).
> ACPI: PCI interrupt 0000:00:0b.1[A] -> GSI 5 (level, low) -> IRQ 5
> bt878(1): Bt878 (rev 17) at 00:0b.1, irq: 5, latency: 32, memory:
> 0xde014000 attach: checking "bt878 #0 [hw]"
> find by pci: checking "bt878 #0 [hw]"
> attach: "bt878 #0 [hw]", to card 0
> attach: checking "bt878 #1 [hw]"
> find by pci: checking "bt878 #1 [hw]"
> attach: "bt878 #1 [hw]", to card 1
> DVB: registering new adapter (DST).
> DVB: registering new adapter (DST).
> bt878 find by dvb adap: checking "DST"
> dst_check_ci: recognize DTTDIG
VP-3020/3021------------------> You have a good signal ?


Manu
> DST type : terrestial TV
> DST type flags :
> DVB: registering frontend 0:0 (DST TERR)...
> bt878 find by dvb adap: checking "DST"
> dst_check_ci: recognize DTTDIG
> DST type : terrestial TV
> DST type flags :
> DVB: registering frontend 1:0 (DST TERR)...
>
> Simon